An 80×200 steel building gives you 16,000 sq ft (1,486 m²) of clear-span, column-free floor with a long 200-foot sidewall built for flow. In 2026, an 80×200 runs roughly $1.89M–$2.91M CAD turnkey ($118–$182/sq ft), or from about $352,000 as an engineered kit. The length suits dock-heavy distribution, long production lines, and cross-dock layouts where trucks load along the wall while the 80-foot clear width keeps the interior open. See the full Steel Building Sizes hub and the 2026 Commercial Steel Building Cost Guide, or open the Cost Calculator and quote tool.
Key Takeaways
- Footprint: 80 ft wide × 200 ft long = 16,000 sq ft (1,486 m²), fully clear span with no interior columns.
- Turnkey price: about $1.89M–$2.91M CAD ($118–$182/sq ft) in 2026 — foundation, erection, insulation, finishes, MEP rough-in, and permits included.
- Kit / shell: engineered kit from ~$352K; weather-tight shell ~$688K–$1.15M.
- Best for: dock-heavy distribution, long production and assembly lines, and cross-dock logistics.
- Eave & docks: typical eave 18–28 ft; the 200 ft sidewall supports a large bank of dock doors.
- Engineering: pre-engineered to CSA A660 and NBCC 2020 with stamped, province-specific drawings included.
Why Titan Is Your Trusted Steel Building Manufacturing Partner in Canada
One accountable Canadian manufacturing partner — from design and engineering to delivery and erection.
100% Canadian company
Canadian-made steel buildings, supplied and supported from within Canada.
25 years of experience
Decades designing and delivering steel buildings for Canadian businesses.
P.Eng-stamped engineered drawings
Engineered to the National Building Code of Canada and your provincial code for local snow, wind and seismic loads.
CSA A660-compliant fabrication
Built in a CWB / CSA W47.1 certified facility.
In-house DAAS & MBS designers
Metal Building Software specialists for structural and pre-engineered (PEMB) design.
End-to-end project support
Design, engineering, fabrication, delivery and erection coordination through one manufacturing partner.
What a 80×200 Steel Building Costs in 2026
Titan prices an 80×200 in three tiers, so you buy only the scope you need. The ranges below apply Titan’s 2026 per-square-foot rates to 16,000 sq ft; the same rates drive the comparison figures on the Steel Building Sizes hub.
| Package | What’s Included | Total Range (CAD) | Per Sq Ft |
|---|---|---|---|
| Engineered Kit | Primary frames, purlins, girts, bracing, anchor bolts, fasteners, and NBCC/CSA A660 stamped drawings | $352,000 – $688,000 | $22 – $43 |
| Building Shell | Kit plus roof and wall cladding, trim, gutters, and framed openings to weather-tight stage | $688,000 – $1,152,000 | $43 – $72 |
| Turnkey | Kit + foundation + erection + insulation + interior finishes + MEP rough-in + permits | $1,888,000 – $2,912,000 | $118 – $182 |
What Drives the Cost of a 80×200
On a 16,000 sq ft building, the dock count is often the single biggest variable, alongside clear height, insulation, and regional loads. The table shows the direction each pushes cost.
| Cost Variable | Directional Impact on Price |
|---|---|
| Dock doors & levellers | The 200-foot wall supports many docks; each position with door, leveller, seal, and bumpers is a fixed line item and a major driver on distribution builds. |
| Eave height | 18 ft to 28 ft adds wall steel across 560 linear ft of perimeter; high-bay racking sits at the taller end. |
| Insulation system | Conditioned or cold-chain envelopes using spray foam or insulated metal panels raise cost over a basic shell. |
| Snow & wind loads | Regional ground-snow and wind loads add frame tonnage across the 200 ft roof line. |
| Foundation & floor | A slab engineered for heavy forklift and truck loads, plus dock-pit detailing, changes the foundation cost. |
| Interior finishes & services | Offices, sortation mezzanines, and MEP rough-in move a shell toward turnkey and set the high end of the range. |
What a 80×200 Steel Building Is
An 80×200 steel building is a pre-engineered metal building (PEMB) measuring 80 feet wide by 200 feet long — 16,000 square feet of column-free floor. The long 200-foot footprint is built for flow rather than square area: a production or assembly line has room to run end to end, deep racking runs line up along the length, and the 200-foot sidewall carries a large bank of dock doors for high-throughput distribution — all while the 80-foot clear width keeps drive lanes and staging open. “Pre-engineered” means the frame is designed and fabricated to your site’s exact snow, wind, and seismic loads before shipping, then bolted together on site, with stamped, province-specific drawings included. See how the 80×200 sits among neighbouring sizes on the Steel Building Sizes hub.
Province-by-Province Pricing
The per-square-foot ranges above are Canada-wide; where you build shifts the finished cost through snow load, seismic design, labour rates, and freight distance. The modifiers below are directional — your quote reflects your municipality’s actual code requirements.
| Province / Region | Directional Modifier | Why |
|---|---|---|
| Ontario | Baseline | Deep supplier and trade base near the GTA keeps steel logistics and erection crews competitive. |
| Alberta | Near baseline to slightly lower | Strong industrial construction capacity and moderate seismic demand keep costs efficient outside the mountains. |
| Saskatchewan / Manitoba | Slightly higher | Heavy ground snow loads add frame tonnage, and longer freight hauls to remote sites raise delivery cost. |
| British Columbia | Higher | Coastal seismic design and elevated labour rates increase both engineering and erection. |
| Quebec | Slightly higher | High snow loads and provincial code and permitting steps add to the finished cost. |
| Atlantic Canada | Higher | Coastal wind exposure plus freight distance to the Maritimes lift cladding and shipping line items. |
What You Can Build in a 80×200
The 16,000 sq ft clear span, in a long footprint, makes the 80×200 a natural distribution and production building. Common uses include a dock-served steel warehouse or logistics hub, a long manufacturing or assembly line, and a cross-dock facility with doors on both sidewalls. As a fully engineered industrial building, it can be zoned into production, storage, and office areas within one shell.
Sample 80×200 Builds Titan Delivers
Dock-heavy distribution centre
An 80×200 lines a bank of dock doors along the 200-foot wall for high-throughput regional or last-mile distribution — a right-sized logistics hub that keeps trucks moving and the floor open.
Long production or assembly line
Two hundred feet of clear span gives a continuous manufacturing or assembly line room to run, with a mezzanine control room overlooking the floor.
Cross-dock logistics facility
With doors on both sidewalls, an 80×200 becomes a drive-in, drive-out cross-dock building for fast transfer between inbound and outbound trailers.
80×200 vs Other Common Sizes
The 80×200 is Titan’s long-span distribution size. Compare turnkey pricing with its nearest neighbours, then open any size for full detail.
| Size | Floor Area | Turnkey Range (CAD) | Per Sq Ft |
|---|---|---|---|
| 80×150 | 12,000 sq ft | $1.42M – $2.18M | $118 – $182 |
| 80×200 (this page) | 16,000 sq ft | $1.89M – $2.91M | $118 – $182 |
| 100×200 | 20,000 sq ft | $2.36M – $3.64M | $118 – $182 |
| 120×200 | 24,000 sq ft | $2.83M – $4.37M | $118 – $182 |
Frequently Asked Questions
How much does an 80×200 steel building cost in Canada?
An 80×200 (16,000 sq ft) steel building typically costs about $1.89M to $2.91M CAD turnkey in 2026, which works out to roughly $118 to $182 per square foot. As an engineered kit only it starts around $352,000. The number of dock positions is often the biggest single variable within that range.
How big is an 80×200 steel building?
An 80×200 is 16,000 square feet — 80 feet wide by 200 feet long, or about 1,486 square metres. Because it is clear span, all 16,000 square feet is column-free, and the long footprint suits flow-through distribution and production.
Is an 80×200 steel building fully clear-span?
Yes. The full 80-foot width is engineered as a clear span with no interior columns, so racking runs and material flow move uninterrupted down the 200-foot length.
How many dock doors fit on an 80×200?
The 200-foot sidewall typically supports six to eight dock doors at standard spacing, each with a leveller and seal, and you can add doors on the second sidewall for cross-docking. Exact placement depends on the frame bay layout.
Is an 80×200 good for cross-docking?
Yes. Doors on both 200-foot sidewalls create a drive-in, drive-out cross-dock flow, so freight transfers straight from inbound to outbound trailers without deep storage — a common last-mile and freight-consolidation layout.
What eave height suits an 80×200 distribution centre?
Distribution centres commonly specify 24 to 28 feet for high-bay racking, while lighter uses run 18 to 24 feet. Taller eaves add wall steel across the long perimeter, so match the height to your racking and equipment.
Can an 80×200 run a full production line?
Yes. Two hundred feet of clear span suits a continuous manufacturing or assembly line, with room for conveyors, staging, and a mezzanine control room, and the frame can be engineered for an overhead crane if the process needs one.
What foundation does an 80×200 need?
A slab engineered for heavy forklift and truck loads, with dock-pit detailing where docks are required, suits most 80×200 builds. Soil conditions and your equipment loads set the final slab and footing design.
Can an 80×200 be split into zones?
Yes. Demising walls can separate production, storage, and office zones within the same shell, so a single 80×200 can serve several functions while keeping the exterior and dock line unified.
What is the lead time for an 80×200 steel building?
Lead time varies with engineering, provincial permitting, and the current Titan production schedule. Contact Titan for a current timeline for your province and site so you can plan around design, fabrication, and erection.
Is an 80×200 cheaper per square foot than an 80×150?
Usually a little. Spreading fixed costs over 16,000 versus 12,000 square feet tends to lower the per-square-foot rate slightly, though the total project cost is higher. Your exact rate depends on dock count, insulation, and region.
How does an 80×200 compare to a 100×200?
Both are 200 feet long; a 100×200 (20,000 sq ft) adds 20 feet of width for wider racking or aisles at a higher total cost, while an 80×200 (16,000 sq ft) is a leaner long-span footprint. Choose by whether you need extra width or a tighter budget.
Related Resources
- Steel Building Sizes hub — every Titan size with pricing by square foot.
- 2026 Commercial Steel Building Cost Guide — how Canadian steel building pricing is built up.
- 80×150 and 100×200 — the nearest sizes down and up.
- Warehouse, logistics, and manufacturing applications.
- Cost Calculator and quote tool — get an exact 80×200 price for your site.